847-775-0640 Call us M-F 9-5:30 CST

Trigger Systems Sapphire CR44 Refugium

Product code: 8067
FT-TS-CR44

Availability: Usually Ships within 24-48 Hours

$584.99
Reward Points Policy Earn 35,098 AQUAPOINTS
OR
Trigger Systems Sapphire CR44 RefugiumTrigger Systems Sapphire CR44 Refugium
Trigger Systems Sapphire CR44 Refugium Trigger Systems Sapphire CR44 Refugium Trigger Systems Sapphire CR44 Refugium Trigger Systems Sapphire CR44 Refugium Trigger Systems Sapphire CR44 Refugium Trigger Systems Sapphire CR44 Refugium Trigger Systems Sapphire CR44 Refugium Trigger Systems Sapphire CR44 Refugium

Frequently bought together

Trigger Systems Sapphire CR44 Refugium

Sapphire CR44 Sump Features:

  • Interchangeable plates
  • Configurable input fitting plate (2 provided)
  • Fully enclosed polycarbonate lid to prevent splashing
  • Two additional input fittings that can be placed in the skimmer or return section
  • Four quick connect hose input fitting for dosing or ATO inputs
  • Adjustable water height
  • Four position probe holder with countersunk mounts
  • Self-adjusting foam block platform
  • Cable/hose organizers
  • Dual acrylic platforms
  • Protein skimmer section
  • Refugium section
  • Sapphire blue and Aquamarine blue coloring to block light and prevent unwanted algae growth in other sections, solid white bottom
 
 


Specifications

  • Dimensions: 44" long x 16" wide x 15" high
  • Drain Input Fittings: 2 x 1.5" plus blank plate
  • Mechanical Filter: 3 x 4" filter sock and/or foam block
  • Skimmer Section: 14" x 15.5"
  • Center/Refugium Section: 14.5" x 15.5"
  • Return Pump Section: 7" x 15.5"
  • Total Water Volume: 43 gallons
  • Skimmer Water Level: 7" - 9.5" adjustable

 

Interchangeable Plates - Patent Pending
Each Sapphire sump comes with two plates that can be placed into Section 1:

  • Filter Sock Plate
  • Foam Block Plate
 

The filter sock plate is installed when the included 100 micron filter socks are desired.

The foam block plate is perforated with holes and comes with a foam sponge block filter. The foam block plate can be used when filter socks are not desired or in the case when the filter socks need to be changed or cleaned but replacements socks are not readily available but yet mechanical filtration is needed. In this case, simply remove the filter sock plate and install the perforated foam block plate and then place the included foam sponge block filter in place.

Configurable Input Plate

The drains from the sump will connect to the plate that has two 1.5" input fittings. If the drain configuration of your tank requires a different number or size of inputs to the sump, there is a blank input plate that can be drilled to meet those requirements.

There are two additional input fitting mounts that can be installed in two locations in the skimmer section or in one location in the return section. One of these has a single 1" input fitting and the other has a single 1.5" input fitting. 

Fully Enclosed Polycarbonate Lid

The plate area is covered with a full piece polycarbonate lid to prevent splashing and noise. Polycarbonate material is used to prevent the lid from bowing over time. There is a finger notch in the front of the lid to assist in removal.

Quick Connect Hose Input Fittings

Located in the top bracing of the sump, these 1/4" connections allow tubing for dosing or the ATO to be implemented

Adjustable Water Level
Water level in the sump is adjustable from 7” to 9.5” to accommodate for the water height requirements for different protein skimmers. 

Self Adjusting Foam Block - Patent Pending
As the water level is adjusted by sliding the wall up and down, the foam block sponge filter and the perforated plate that it sits on will also move up and down automatically. This is important to maintain the correct location of the foam block sponge filter with respect to the sump water height. 

Probe Holder
The CR44 sump comes with a probe holder that can hold up to four probes. Three of the holes are 0.5” in diameter and one of the holes is 0.7” in diameter to fit different sized probes. These holes are countersunk so that the probes do not fall through. There are 8 o-rings provided that help to secure the probes nicely into the holders without damaging the probes.  

Cable and Hose Organizer

Keep the cords and hoses tidy with the two provided holders, located above the probe holders and return section.

 

Questions on Trigger Systems Sapphire CR44 Refugium

No questions asked yet

Ask Your Own Question






  1. works very well Review by Brad
    Product Rating:

    shame I can't submit pics but my build turned out very well. One small design flaw is there's no way to clean out the area where the water is returned into the sump. To fix that I just used flexible tubing instead of hard pipe. Other then that works like a dream compared to my old sump. Got this for a 200 gallon reef setup. Delivered quicker then expected and never seen a box so well designed. This thing could have fell out off an airplane and be ok. Not one scratch or even finger print on it. Very imptessed on aquacave and will not be my last order from them. Even called prior to shipping just to make sure the address was correct. 5 stars! (Posted on 5/14/2020)


Write Your Own Review

You're reviewing: Trigger Systems Sapphire CR44 Refugium

How do you rate this product? *

Product Rating: 1 stars 2 stars 3 stars 4 stars 5 stars
584.99 In stock
  Loading...